GYEON Q2 Leather Shield

Shield all types of leather with just one application!

GYEON Q2 Leather Shield uses advanced quartz technology to create a protective shield on your leather. The superior protection provided by GYEON Q2 Leather Shield protects against dirt, UV rays, and the rigors of everyday use. GYEON Q2 Leather Shield has been tested on all modern leathers to date and is safe for use on each of them! GYEON Q2 Leather Shield does not stiffen your leather surface, or make it more slippery and greasy – it makes it shielded!

Due to constant exposure to harsh elements, your leather surfaces, if left untreated, tend to fade and wear quicker than other sections of your car. The rubbing of your pants or jeans on the seat, harsh UV rays, spilled drinks and food all cause staining, drying, scarring, and a general fading. Properly cared for leather is easier to maintain, so make sure you protect from the beginning with GYEON Q2 Leather Shield!

GYEON Q2 Leather Shield uses an advanced SiO2 (silicon dioxide) based formula, specifically developed for automotive leather interiors. This specialized formula creates a strong barrier between your leather and harmful elements that cause degradation. GYEON Q2 Leather Shield is very easy to apply, requires only one application for supreme protection, and will not alter the look or feel of your leather surfaces.

For a shielded, matte leather surface, GYEON Q2 Leather Shield is perfect!


GYEON Q2 Leather Shield is very easy to apply! First, be sure your leather surface is cleaned using a dedicated leather cleaner. Apply a few drop of product ontot the suede microfiber towels included in the kit and use the included applicator to apply an even layer. Allow to dry without wiping off and you’re done!

Directions for use:

  • First, clean your leather surface with GYEON Q2m Leather Cleaner.
  • Apply a moderate amount of product with the attached suede applicator. Be sure to apply even application.
  • Leave the surface to dry without wiping off.
  • Enjoy fully coated, protected, and shielded leather!

50 ml

CLICK HERE – http://www.autogeek.net/gyeon-q2-leather-shield.html

Meguiar’s Perfect Clarity Glass Care Kit

Everything you need for perfect clarity glass!

Meguiar’s Perfect Clarity Glass Care Kit uses two products to deep clean your glass and remove water spots, as well as protect and repel rain and water for months – all in two easy steps! Meguiar’s Perfect Clarity Glass Polishing Compound uses microscopic abrasives to gently remove stains, grime & water spots that glass cleaners leave behind. Meguiar’s Perfect Clarity Glass Sealant protects your newly cleaned glass surface and improves your overall visibility for months!

Having dirty and smeared glass windows and front and rear windshields is more than just an eyesore. It can also be very dangerous! If you don’t have perfect clarity in your windows and glass extreme driving conditions like rain and sun glares can cause an accident. Meguiar’s Perfect Clarity Glass Care Kit takes care of each step needed for perfect glass!

Meguiar’s Perfect Clarity Glass Polishing Compound is a deep cleaning formula that removes stains and grime that traditional glass cleaner can leave behind. Even hard to remove stains and residue are no match! Using advanced micro-abrasives, Meguiar’s Perfect Clarity Glass Polishing Compound helps restore the clarity in your neglected, grimy glass surfaces and prepares glass to be treated with Meguiar’s Perfect Clarity Glass Sealant.


First, remove stains and grime from your glass using the Meguiar’s Perfect Clarity Glass Polishing Compound and the yellow Meguiar’s applicator. Once the surface contaminants are removed, use a microfiber towel to buff away excess product.
Once your glass has been cleaned, use the gray foam block applicator to apply the Meguiar’s Perfect Clarity Glass Sealant. Once the application is complete you have cleaned and protected glass for months!

Just as the name implies, Meguiar’s Perfect Clarity Glass Sealant protects your paint and repels water making your glass easier to clean and maintain. Thanks to highly durable polymers in the Meguiar’s Perfect Clarity Glass Sealant formula, an invisible barrier that repels rain is formed. This makes oil and grime easier to remove and dramatically improves wet weather driving visibility.

Meguiar’s Perfect Clarity Glass Care Kit also includes two applicators, one needed for each product, so just this one kit gets you the perfect window and glass clarity you always needed!

Meguiar’s Perfect Clarity Glass Care Kit includes:

4 oz. Meguiar’s Perfect Clarity Glass Polishing Compound
4 oz. Meguiar’s Perfect Clarity Glass Sealant
Meguiar’s Foam Applicator pad (use with Polishing Compound)
2 x 3 inch Gray Foam Applicator (use with Glass Sealant)

CLICK HERE – http://www.autogeek.net/meguiars-perfect-clarity-glass-kit.html

Complete Car Wash System with Dolly – GRAY (NEW COLOR)

Protect your paint with our all-inclusive wash system.

Most of the fine swirls and hairline scratches on your vehicle’s paint appeared during washing. Swirls occur when a piece of dirt is trapped between the wash mitt and the paint. The dirt is rubbed into the paint, leaving the tell-tale spider webbing. The most lubricated car wash cannot make up for a dirty wash mitt. Prevent wash-induced swirls with the Complete Wash System with Dolly.

The Complete Wash System with Dolly keeps your wash mitt or sponge cleaner, with no additional steps on your part. By trapping dirt in the bottom of the wash bucket, this wash bucket system drastically reduces the amount of dirt transferred back onto your vehicle from the wash bucket.

Here’s how it works: normally, you wash a section of paint and then dip your mitt into the bucket of soapy water. You immediately continue washing on the next section. So, what happened to the dirt you just removed from the vehicle? It’s in the mitt and the wash bucket, and you’ve just transferred it back onto the vehicle.

The Complete Wash System with Dolly includes a Grit Guard, a raised grid surface that stands about 2.5 inches off the bottom of the bucket. Fill the bucket with your favorite shampoo and water. Load your mitt with soapy water and wash as usual. When you dunk the mitt back in the bucket, drag it across the grid to remove dirt that has accumulated in the nap.The dirt will fall into the grid’s four quadrants and settle in the bottom of the bucket. Even though you agitate the top water every time you reload the mitt, the Grit Guard® stabilizes the water in the bottom of the bucket so the dirt does not rise. Simply stated, your wash water stays clean so your mitt stays clean. Clean mitts mean no swirls!

The Complete Wash System with Dolly includes:

Grit Guard®
The Grit Guard is the revolutionary tool that keeps your wash water clean! It stabilizes the water and allows dirt to fall to the bottom of the bucket where it can’t re-contaminate your wash tools. No swirls or scratches!

5 Gallon Bucket
This big bucket is perfect for washing your vehicle, boat, RV, or ATV. You won’t run out of soapy water before the job is done. The bucket is also perfect for transporting and organizing detailing tools. You can fit a lot of supplies in a 5 gallon bucket!

Gamma Seal® Lid
The system includes a lid for the 5 gallon bucket. This isn’t like a recycled paint bucket – this lid forms a watertight seal. You can fill the bucket with water and transport it without the lid leaking! For car collectors who participate in car shows, this is a great feature. Believe it or not, some of these enthusiasts use nothing but distilled water on their vehicles and they’ll actually bring it to the car show if it’s not available on site. That’s dedication!

Seat Cushion 
Sit on the lid of the bucket and roll around your vehicle to detail wheels and lower panels comfortably. The cushion is dense foam for padded comfort while you work. A cut-out handle makes it easy to carry the cushion to other functions, like sporting events.

5-Wheel Dolly
The dolly accommodates any 3.5 – 7 gallon bucket and has 5 heavy-duty casters capable of supporting up to 250 pounds. Two locking casters hold the dolly still on an incline while three thumb screws hold the bucket in place inside the dolly.

Say goodbye to swirls and scratches! The Complete System with Dolly reduces cross-contamination to protect your paint from the number one cause of swirls.

CLICK HERE – http://www.autogeek.net/complete-wash-system-gray.html

 

NEW Autogeek Embossed Metal Sign

Can you really call yourself an Autogeek without this!?

The Autogeek Embossed Metal Sign is the epitome of your Autogeek obsession (well it is for us, at least!) and no garage, detail shop, or living room is complete without it! Autogeek Embossed Metal Sign is manufactured with aluminum and a lot of Autogeek love. Measuring 20.5” x 17.5”, the Autogeek Embossed Metal Sign is the perfect size for hanging, not too big and not too small! Complete your Autogeek Gear collection of T-Shirts, Hats, Tervis Tumblers, Coolers, and all the other collectibles you have with the Autogeek Embossed Metal Sign!

No garage or detail shop is complete without the Autogeek Embossed Metal Sign!

CLICK HERE – http://www.autogeek.net/autogeek-metal-sign.html

NEW Simple Chuck’s Double Chuck Spotless Water System

Get clean, di-ionized water – simply!

Simple Chuck’s Double Chuck Spotless Water System is a water de-ionization unit that provides approximately 400 gallons of “spotless” water, allowing you to wash your car without fear of water spots! Manufactured to be as simple to use as possible, Simple Chuck’s Double Chuck Spotless Water System features a stainless steel input hose, a pressure regulator, quick disconnects for input/output hoses, wheels, and foldable handle, and is shipped to you with a fresh set of cartridges – once it’s delivered you are ready to go!

There are a lot of outside factors to consider when washing or detailing your car – UV rays, wind, water restrictions, temperature, etc. But one thing you may not have considered? The type of water you’re using! In many areas “hard” water is common – meaning that your water has high levels of minerals included. Why don’t we like hard water? Water spots, of course!

When hard water is allowed to dry on your vehicle’s surface, the included minerals dry onto the surface as well, creating those dreaded water spots. If not treated, water spots, while unsightly, can also cause etching in your clear coat – sometimes even permanent damage! The trick to avoiding water spots to dry your vehicle’s surface right after washing (and we mean RIGHT after!). But what if you had clean water to begin with?

That’s where the Simple Chuck’s Double Chuck Spotless Water System comes in! This easy-to-use water de-ionization system takes your hard water and makes it soft! You can now wash your car with a total water-spot-free peace of mind! 

Simple Chuck’s Double Chuck Spotless Water System uses a negatively and positively charged ion resin to chemically remove all the salts, minerals, and spot-causing particulates in the water. When do you need new filters? When they turn gold! Until they change color, you can use the Simple Chuck’s Double Chuck Spotless Water System as many times as you need it (number of washes vary based on different water “hardness”).

Keep your car washes water-spot free with Simple Chuck’s Double Chuck Spotless Water System – it’s so simple, even Chuck can use it! (In case you’re wondering who Chuck is, he’s the founder of CR Spotless who refuses to use anything unless it’s easy – he’s our kind of guy!)

Replacement filters are available for purchase separately.

This product is drop shipped from the manufacturer via ground service only. International shipping is not available. Additional discounts not applicable.

CLICK HERE – http://www.autogeek.net/simple-chuck-water-system.html

Griots Garage Ultimate Car Wash Bucket with Lid & Casters


The car wash bucket you never knew existed!

Griots Garage Ultimate Car Wash Bucket is proof that not all buckets are created equal. This masterpiece of thoughtful engineering is designed and constructed so well it almost doesn’t feel right calling it a bucket, something that is normally cheap and used for projects around the house. This must-have detailing accessory was designed from the ground up to be the hands-down ultimate car wash bucket, bar none. A lower grill allows heavy grit to sink to the bottom where it can’t contaminate your Wash Mitt. An upper grill holds your wash tools. Genius!

The Ultimate Wash Bucket has a built in measuring cup for your car wash soap!

Built-in measuring cup ensures you never use too much or too little Car Wash!
The lower grid traps dirt particles, while the upper grid is perfect for storing brushes

The lower grid traps dirt particles; the upper grid is perfect for holding wash mitts and wheel brushes

Repeat after me: 6 gallons of water. No, that’s not a typo! The Ultimate Car Wash Bucket by Griot’s Garage holds a massive 6 GALLONS of water! Never again will you have to reload your wash bucket with water and soap halfway through your routine wash.

There are several reasons why the Ultimate Wash Bucket will quickly become your most valuable detailing tool. First and fore most, a lower grill allows heavy grit to sink to the bottom where it can’t contaminate your Wash Mitt. An upper grill holds your wash tools. Last, but certainly not least, a molded-in measuring cup(patented design) allows you to dispense the perfect amount of Car Wash. Unbelievable!

The Ultimate Wash Bucket sold at Autogeek is packaged with 2” casters to make it easy to roll around your driveway. We also include a snap-on lid, perfect for storing your supplies in the bucket after you wash the vehicle.

The Ultimate Wash Bucket is 19” wide, 9” across and a generous 9” deep. It’s so big you can even use one of our Montana Boar’s Hair Car Wash Brushes with it!

Enjoy the absolute best!

Drying Tips

1. Dry the windows and mirrors first. A series of careful firm strokes with your California Water Blade will remove any remaining water.

2. Use the large The Supreme Guzzler to remove the majority of water from your vehicle. This towel measures 20”x 40” and it absorbs seven times its own weight in moisture. Go back over the vehicle with a smaller towel, like the The Guzzler(16”x 24”) to catch any water the large towel may have missed. This quick two-step process will leave your vehicle bone-dry and ready for wax.

CLICK HERE – http://www.autogeek.net/griots-garage-ultimate-car-wash-bucket.html

Dr. Beasley’s Matte Wheel Seal

Spray on sealant for your matte wheels!

Dr. Beasley’s Matte Wheel Seal is a high-tech wheel coating designed specifically for matte wheels and will prevent the build-up of brake dust and road grime. Featuring an extremely high heat resistance, Dr. Beasley’s Matte Wheel Seal will last even under intense heat and use! Dr. Beasley’s Matte Wheel Seal provides absolutely no shine to matte wheels – it just protects!

Due to extremely high temperatures generated by your wheels, finding the right coating or sealant for your wheels’ finish can be tough. Compound that with having a matte wheel finish and you may be searching for ages! But not anymore – Dr. Beasley’s Matte Wheel Seal is designed, as the name suggests, for matte wheels and will protect against brake dust, etching, pitting, and paint erosion!

Dr. Beasley’s Matte Wheel Seal is as easy as spray on, wait, and wipe off!

Brake dust is one of the hardest residues to clean when it comes to car detailing. If regular maintenance and the correct preventative measures are not taken, it can easily take you hours to clean out thoroughly! If not addressed, ferrous brake dust can cause etching, pitting, staining, and paint erosion. Dr. Beasley’s Matte Wheel Seal will provide a layer of protection between your wheels’ surface and this ferrous brake dust, preventing any damage!

Matte finishes are quickly becoming one of the most popular features to have on your car, and matte wheels are no exception! Keep your matte wheels clean, brake-dust free, and protected with Dr. Beasley’s Matte Wheel Seal!

Directions for use:

1. Before use, make sure your wheel is clean and dry.
2. Apply Dr. Beasley’s Matte Wheel Seal using a soft cloth or microfiber applicator.
3. Let the coating cure by leaving it on the surface for several minutes before using a soft microfiber towel to buff off.
4. For maximum results, first clean your wheels using Dr. Beasley’s Matte Wheel Cleanser.

12 oz.

CLICK HERE – http://www.autogeek.net/beasleys-matte-wheel-seal.html

MTM Hydro PF22 Professional Foam Cannon

Create your very own driveway foam party!

MTM Hydro PF22 Professional Foam Cannon is a foaming lance designed to provides the ultimate foaming car wash experience. Used with your pressure washer, the MTM Hydro PF22 Professional Foam Cannon offers adjustable fan blades AND an adjustable spray pattern, either horizontal or vertical, allowing you to make each wash just your own! Sturdily built using heavy plastic and brass, the MTM Hydro PF22 Professional Foam Cannon is a car washing game changer!

If you haven’t used a foam cannon to wash your car, now is the time! Using a foam cannon, whether you are a professional detailer or an enthusiasts keeping up with your own cars, cuts your washing time down dramatically, while also providing a safe environment in which to remove surface contaminants.

MTM Hydro PF22 Professional Foam Cannons give you a huge blast of foam!

When dirt, dust, and other debris are on your vehicle’s surface, even the slightest touch can scratch or mar your finish. You probably know all about using a high lubricity shampoo and a super soft washing medium for a safe dirt removal, but adding a foam cannon to the equation makes it even better! The foam provided by the MTM Hydro PF22 Professional Foam Cannon is a thick layer that fully encapsulates dirt and other debris on the surface, allowing you to remove the contaminants without harm!

Aside from the safety aspect, using a foam cannon like the MTM Hydro PF22 Professional Foam Cannon cuts your car washing time like you wouldn’t believe. Instead of washing and rinsing one panel at a time, you can fully coat the vehicle in a thick foam, allow time to dwell on those tougher grime areas, and work your way around the vehicle with your wash mitt. While a bucket and Grit Guard is still necessary, using the MTM Hydro PF22 Professional Foam Cannon saves you time! And we all know, time is money!

What sets the MTM Hydro PF22 Professional Foam Cannon apart from others is the adjustable foam settings never before seen in a foam cannon. Not only are you able to adjust the fan blades, but you can now adjust the spray pattern as well! MTM Hydro PF22 Professional Foam Cannon will spray thick suds both vertically and horizontally!

Foam cannons make washing your car easier than ever! Foam cannons make washing your car easier than ever!

Use your MTM Hydro PF22 Professional Foam Cannon to keep your car wash safer, quick, and better yet, more fun!

MTM Hydro PF22 Professional Foam Cannon comes with two commonly used fittings for your pressure washer (pictured). If the included fitting is not the fitting you need, please see the options below that can be purchased separately.


Not sure which fitting you need? We can help!

The Foam Cannon HP attaches to the trigger/gun assembly for your pressure washer in the exact same way that your wand currently does.You will just need to remove the wand and look at the fitting that you currently have and match it up to one of the fitting that we offer below. The Foam Cannon HP will connect in exactly the same way. Note: If you have a Karcher K3 X Series pressure washer you will need the Karcher HD/HDS fitting in addition to the Karcher X Series fitting (Sold Separately).

Click here for complete instructions.


1,100 – 5,000 PSI
1.8 – 5.3 GPM
140 degree temp
Adjustable Fan Blades (jet-wide)

CLICK HERE TO BUY NOW – http://www.autogeek.net/hydro-pf22-foam-cannon.html

MTM Featherweight Foam Cannon

All the power of a foam cannon – weighing in at less than a pound!

MTM Featherweight Foam Cannon is a lightweight foaming lance used with your pressure washer to create layers of foam during a wash. Made with military grade aluminum, the MTM Featherweight Foam Cannon is the perfect “entry-level” foam cannon and gets you up and foaming in minutes! Take your ordinary car wash to the next level with the MTM Featherweight Foam Cannon!

Washing your car using a foam cannon has become one of the most popular methods today. The ability to just hook your pressure washer up to a foaming lance and completely cover your entire car in just minutes has more than one advantage and both professional detailers that wash cars full time and detailing enthusiasts that just like to keep their own cars looking perfect are getting on board.

The most important part of using a foam cannon? Having the right tool of course! The MTM Featherweight Foam Cannon is billed as “the perfect foam cannon for entry-level users” – and it really is! Priced just right, and not too heavy, the MTM Featherweight Foam Cannon can be used by anyone – no experience required!

But that’s not to say the MTM Featherweight Foam Cannon doesn’t perform! Thanks to the military grade aluminum lance that adjusts to your desired spray pattern, MTM Featherweight Foam Cannon produces foam that is quick to coat your entire vehicle in a high lubricity foaming shampoo. This foam helps you remove dirt and debris from the surface of your car without harm!

MTM Featherweight Foam Cannon comes with a ¼” quick connect plug, tube, and bottle. The fitting needed to match your pressure washer is sold separately below.

The MTM Featherweight Foam Cannon might be small, but it still delivers excellent amounts of foam!

 

Not sure which fitting you need? We can help!

The Foam Cannon HP attaches to the trigger/gun assembly for your pressure washer in the exact same way that your wand currently does.You will just need to remove the wand and look at the fitting that you currently have and match it up to one of the fitting that we offer below. The Foam Cannon HP will connect in exactly the same way. Note: If you have a Karcher K3 X Series pressure washer you will need the Karcher HD/HDS fitting in addition to the Karcher X Series fitting (Sold Separately).

Click here for complete instructions.

 


Features:

PSI Rating: 1,100 – 2,600
GPM: 1.4 – 2.4
Max temperature: 140 degrees

CLICK HERE TO BUY NOW – http://www.autogeek.net/featherweight-foam-cannon.html

RimSavers Rim & Wheel Protection

RimSavers Rim & Wheel Protection

For maximum wheel and rim protection!

RimSavers are a durable and lightweight barrier designed to protect your wheels and rims from the dreaded “curb rash”. Constructed using a lightweight and durable material, RimSavers make for a very easy DIY project, while still providing ultimate protection. Each RimSaver has a guide “lip” on the top side of the blade that offers easier installation and extra protection. Each RimSavers kit includes 4 cut strips that fit up to a 24” wheel – they’re fully customizable for you! 

Imagine – you’ve just spent over $1,400 on brand new Black KMC XD Series XD831 wheels, you’re driving around town showing them off and you accidentally clip a high curb, scratching up your wheels’ finish. What do you do? After a few choice words, you’d probably start the process of getting them repaired and refinish. BUT, if you had RimSavers installed on your wheels, this wouldn’t be an issue!

RimSavers are a thin strip of protective material that you fit around the lip of your wheels’ rim. This strip absorbs the scratching that is most often caused by errant curbs, saving your rims’ finish. Hence the name, RimSavers! They adhere to your rim using a very high bond tape that will not warp or degrade when exposed to high temperatures.

RimSavers fit perfectly on the lip of your rim for a complete hold on your wheels!

RimSavers can be installed WITHOUT the removal of the wheel and can easily be installed by anyone – no professional experience required! In addition to providing protection to your wheels, RimSavers add that extra aesthetic touch as well. Do you have red paint and black wheels? Try the RED RimSavers for a nice accent. Black paint with silver wheels? Go for the BLACK RimSavers! Whatever color combination you choose, RimSavers will add a subtle increase in appearance.

Each RimSavers kit includes four (4) cut strips that can fit up to a 24” wheel, cleaning wipes and adhesive primer wipes to ensure a long and lasting bond to the alloy wheel surface, and joining clips and glue to finish the installation.

RimSavers area available in the following colors:

Keep your wheels and rims protected from the unexpected clipping of curbs with RimSavers!

Check out the full installation instruction PDF HERE or watch the video below!